Westell 327w installation manual default user and passwork

Select New Location from the Location field. The Network screen shows the settings for the newly created location. From the Configure field in the Network screen, select Built-in Ethernet. The Getting Started screen will be displayed. You may now begin your Account Setup. If you want to set up advanced features for VersaLink, follow the instructions provided in sections 11 through HOME As you navigate through the various screens of VersaLink, the name of the active page that you have selected will appear in the upper-left corner of the screen, as shown below.

Please note that the actual values may differ from the values displayed in the screens. If you do not want to change your connection profile, click on close in the screen. Note: The actual values may differ from the values displayed in this screen.

DSL Connection Information Click on enable. VersaLink must be reset to allow the new configuration to take effect. Click on OK. If you clicked OK in the preceding screen, the following screen will be displayed. VersaLink will be reset and the new configuration will take effect. After you enable Single Static IP, you must reboot your computer. This screen will allow the modem to be reset and the new configuration will take effect. After you disable Single Static IP, you must reboot your computer.

Westell has developed an extensive list of NAT services and you may select any service from this list. By selecting your specific NAT service and setting up a NAT profile, you will ensure that the appropriate ports on VersaLink are open and that the required application traffic can pass through your LAN.

UPNP Enable The Gateway will be reset automatically, and the new configuration will take effect. After a brief delay, the home page will be displayed. The NAT profile may then be associated with a connection profile, allowing you to customize profiles for specific users. For example, if you want to attach specific NAT services to a profile, or if you want to set up a different connection setting for a profile, you can create new NAT profiles and customize them to your preference.

If you select edit from the Service Configuration screen, the following screen will be displayed. By selecting the edit button, you can make changes to your profile name, and then add NAT services to or delete them from your profile. Click OK to save your new profile settings. If you click on Cancel, your new profile settings will not be saved. Remember, you may attach an unlimited number of NAT services to any profile.

After you have selected a service, click enable. If you click enable, the following pop-up screen will be displayed. If you click OK, you will allow incoming connections to be forwarded to a designated local PC. The Host Device screen will allow you to select which device will host the NAT service you selected on your local area network.

Security Level High High security level only allows basic Internet functionality. All other traffic is prohibited. This screen allows you to change the security parameters on your Inbound and Outbound Firewall rules via the User Defined Firewall Rules drop-down arrow. If you need to reset VersaLink to factory default settings, push the reset button on the rear of VersaLink. This screen gives a detailed explanation of the Firewall Rules.

When disabled, no stations will be able to connect to the VersaLink. Beacon Period The time interval between beacon frame transmissions. Beacons contain rate and capability information.

Otherwise, the 20 uses slot time is used. Now click on add. If you clicked add, the following screen will be displayed. Westell advises setting this to enabled for the private LAN. This value must be greater than 10 seconds. If you clicked on save, in the preceding DHCP Configuration screen, the following pop-up screen will appear.

The arrows show the data path for each flow. Click on save. A check mark will appear in the box. NOTE: Westell does not recommend that you change this setting. This setting is only valid if one of the Virtual Channels is configured for Bridge mode. Click If you click OK in the preceding pop-up screen, the following screen will be displayed.

If you click on Cancel, the change will not take effect. Click on the connect button to establish a PPP session. Factory defaults become current configuration. If you clicked on OK in the preceding screen, the following screen will be displayed. The WAN Configuration screen will be displayed. After you have made the configuration for this protocol, select the set VC button. Enter the appropriate values in the fields and click on set VC.

If you click the set VC button, the following pop-up screen will be displayed. Click on OK in the pop-up screen. If you click on Cancel, the new settings will not be saved. If you clicked on OK, the following screen will be displayed. The following screen will be displayed If you click edit, the following screen will be displayed.

Enter the appropriate values in the fields and click on set. You can help improve online connections and connect with more players in Back 4 Blood by forwarding some ports.

Get Software. Open Ports for Roblox If Roblox has trouple loading online games or fails to load games then you need to make sure that you have an open port. Opening Ports for Splitgate using Your Router You can help reduce lag and improve your overall experience in Splitgate by forwarding ports in your router.

For Honor Port Forwarding Help improve your online connections and make connecting with others easier in For Honor by forwarding some ports. Select Host or Dynamic to control how the port forwarding service is activated. If you selected "Host" in the previous step, select the computer on your network where this port forwarding service will be applied. You can either select the computer from the drop-down list or enter its IP address.

Review the settings for the rule you have created, and click Close. You may be instructed by a Verizon technical support person to reset your gateway in order to clear any existing properties. You may also have to reset your gateway to the factory defaults if you have forgotten your gateway user name or password. Note: Resetting your router to the factory defaults not only changes your gateway user name and password to the factory default values, but it also deletes all your network settings.

This includes the SSID and network encryption key. After you reset your gateway to the factory defaults, your home network won't be accessible until you reconfigure your router and all your network devices to use the same SSID and network encryption key.

Your VersaLink W gateway is now using the default settings for the network configuration. This includes the default SSID and network encryption key. You must re-configure your VersaLink gateway to match your previous settings that were assigned to all other devices on your wireless network. Otherwise, no other network devices will be recognized. Note : The Westell security screens and prompts may vary slightly from the directions below, depending on when you purchased your Westell gateway and the version of the firmware loaded on it.

To find your WEP encryption key:. Note which key Key 1 - Key 4 is selected in the Key Select drop-down list. If more than one encryption key is entered in the Key 1 - Key 4 fields, the key displaying in the Key Select field is the active encryption key. In the example below, Key 2 is the active encryption key. All network adapters must use the same WEP encryption level.